液力变矩器性能参数的计算误差及其修正方法

罗虹; 王腾腾; 李兴泉; 李英强

doi:10.3969/j.issn.0258-2724.2012.03.019

液力变矩器性能参数的计算误差及其修正方法

doi: 10.3969/j.issn.0258-2724.2012.03.019

基金项目:

重庆市科技攻关重大项目(CSTC,2009AC6002)

详细信息

作者简介:
罗虹(1955 -),男,副教授,研究方向为车辆系统动力学控制与汽车振动控制,电话:18696660312,E-mail:lhongcd@163.com

计量
- 文章访问数: 1759
- HTML全文浏览量: 50
- PDF下载量: 643
- 被引次数: 0
出版历程
- 收稿日期: 2011-06-17
- 刊出日期: 2012-06-25

Calculation Errors of Performance Parameters of Hydraulic Torque Converter and Their Corrections

摘要

摘要: 为提高液力变矩器数值模拟的精度,采用CFD(computational fluid dynamics)方法对液力变矩器的变矩比、效率和泵轮容量系数等性能参数进行了计算,对计算误差进行了分析,并提出了相应的误差修正方法.通过分析补偿油液流动对泵轮容量系数计算误差的影响,提出了针对泵轮容量系数误差的修正方法.结果表明:数值计算模型中,忽略摩擦损失和补偿油液流动的影响,将引起变矩器性能参数的计算误差;针对摩擦损失提出的误差修正方法,使算例中变矩器的变矩比和效率的最大相对误差均由16.2%减小到13.9%;按照泵轮容量系数误差的修正方法,泵轮容量系数的最大相对误差由13.9%减小到7.3%.
- 液力变矩器 /
- 变矩器性能 /
- 数值模拟 /
- 误差修正
Abstract: In order to improve the numerical simulation precision of hydraulic torque converters, the performance parameters, including torque ratio, efficiency and pump capacity factor, were calculated by the CFD (computational fluid dynamics) method. Calculation errors of the performance parameters were analyzed, and the corresponding correction methods were proposed. Through analyzing the impact of compensating fluid flow on the calculation error of pump capacity factor, its correction method was proposed. The results show that the neglect of friction loss and compensative flow in numerical simulations will result in calculation errors of the performance parameters of a hydraulic torque converter. The error correction method for friction loss can decrease the maximal relative errors of torque ratio and efficiency from 16.2% to 13.9%, and the error correction method for pump capacity factor can decrease its maximal relative error from 13.9% to 7.3%.
- hydraulic torque converter /
- characteristics of torque converter /
- numerical simulation /
- error correction

HTML全文

参考文献(15)

LIU Yue.Characteristics prediction of torque converter based on CFD//The International Conference on Electronics, Communications and Control (ICECC2011). Ningbo: IEEE Press, 2011: 4203-4206.

惠记庄,焦生杰,邹亚科,等. 钣金型液力变矩器内部流场的分析[J]. 长安大学学报:自然科学版,2009,29(2): 107-110. HUI Jizhuang, JIAO Shengjie, ZOU Yake, et al. Analysis on flow field of fabrication hydraulic torque converter[J]. Journal of Changan University: Natural Science Edition, 2009, 29(2): 107-110.

严鹏,吴光强,谢硕. 液力变矩器泵轮流场数值分析[J]. 汽车工程,2004,26(2): 183-186. YAN Peng, WU Guangqiang, XIE Shuo. Numerical analysis on pump flow in a torque converter[J]. Automotive Engineering, 2004, 26(2): 183-186.

才委,马文星,刘春宝,等. 基于三维流场计算的液力变矩器特性预测方法[J]. 哈尔滨工程大学学报,2007,28(3): 316-319. CAI Wei, MA Wenxing, LIU Chunbao, et al. Characteristics prediction of a torque converter based on three dimensional numerical calculation of flow field[J]. Journal of Harbin Engineering University, 2007, 28(3): 316-319.

朱建华. 液力变矩器理论设计方法的研究. 重庆:重庆大学,2008.

WANG Jian, GE Anlin, LEI Yulong. Numerical research on the hydraulic performance of a squashed torque converter for automatic transmission//Proc. of the 1st International Conference on Enhancement and Promotion of Computational Methods in Engineering Science and Mechanics. Changchun: Jilin University Press, 2006: 114-118.

DONG Y, LAKSHMINARAYANA B. Experimental investigation of the flow field in an automotive torque converter stator[J]. ASME Journal of Fluids Engineering, 1999, 121(4): 788-797.

张杰山,过学迅,许涛,等. 液力变矩器流道网格生成及内流场数值分析[J]. 武汉理工大学学报,2007,29(7): 106-109. ZHANG Jieshan, GUO Xuexun, XU Tao, et al. Grid generation of torque converter and numerical analysis on internal flow field[J]. Journal of Wuhan University of Technology, 2007, 29(7): 106-109.

才委,马文星,褚亚旭,等. 液力变矩器导轮流场数值模拟与实验[J]. 农业机械学报,2007,38(8): 11-14. CAI Wei, MA Wenxing, CHU Yaxu, et al. Numerical simulation and experimental research on flow field in the stator of a torque converter[J]. Transactions of the Chinese Society for Agricultural Machinary, 2007, 38(8): 11-14.

吴军,谷正气,钟志华. SST湍流模型在汽车扰流仿真中的应用[J]. 汽车工程,2003,25(4): 326-329. WU Jun, GU Zhengqi, ZHONG Zhihua. The application of SST turbulence model in the aerodynamic simulation of the automobile[J]. Automotive Engineering, 2003, 25(4): 326-329.

LIU Yue, PAN Yuxue, LIU Chunbao. Numerical analysis on three-dimensional flow field of turbine in torque converter[J]. Chinese Journal of Mechanical Engineering, 2007, 20(2): 94-96.

WU Guangqiang, YAN Peng. System for torque converter design and analysis based on CAD/CFD integrated[J]. Chinese Journal of Mechanical Engineering, 2008, 21(4): 35-39.

LEE C W, JANG W K, LEE J M, et al. Three dimensional flow field simulation to estimate performance of a torque converter[J]. SAE Technical Paper Series, 2000-01-1146: 1-5.

马文星. 液力传动理论与设计[M]. 北京:化学工业出版社,2004: 32-33.

朱经昌. 液力变矩器的设计与计算[M]. 北京:国防工业出版社,1991: 30-32.

施引文献

附加材料(0)

访问统计