• ISSN 0258-2724
  • CN 51-1277/U
  • EI Compendex
  • Scopus 收录
  • 全国中文核心期刊
  • 中国科技论文统计源期刊
  • 中国科学引文数据库来源期刊

带横肋双拼叠合剪力墙轴心受压性能研究

袁志仁,  朱浩,  吴子瞳,  黄倩雅,  鲍昀,  李道政

袁志仁, 朱浩, 吴子瞳, 黄倩雅, 鲍昀, 李道政. 带横肋双拼叠合剪力墙轴心受压性能研究[J]. 西南交通大学学报. doi: 10.3969/j.issn.0258-2724.20250310
引用本文: 袁志仁, 朱浩, 吴子瞳, 黄倩雅, 鲍昀, 李道政. 带横肋双拼叠合剪力墙轴心受压性能研究[J]. 西南交通大学学报. doi: 10.3969/j.issn.0258-2724.20250310
YUAN Zhiren, ZHU Hao, WU Zitong, HUANG Qianya, BAO Yun, LI Daozheng. Axial Compression Performance of Double-Spliced Composite Shear Walls with Transverse Ribs[J]. Journal of Southwest Jiaotong University. doi: 10.3969/j.issn.0258-2724.20250310
Citation: YUAN Zhiren, ZHU Hao, WU Zitong, HUANG Qianya, BAO Yun, LI Daozheng. Axial Compression Performance of Double-Spliced Composite Shear Walls with Transverse Ribs[J]. Journal of Southwest Jiaotong University. doi: 10.3969/j.issn.0258-2724.20250310

带横肋双拼叠合剪力墙轴心受压性能研究

doi: 10.3969/j.issn.0258-2724.20250310
基金项目: 吉林省自然科学基金项目(YDZJ202301ZYTS497)
详细信息
    作者简介:

    袁志仁(1974—),男,副教授,研究方向为结构工程,E-mail:yzr117@163.com

  • 中图分类号: TU375

Axial Compression Performance of Double-Spliced Composite Shear Walls with Transverse Ribs

  • 摘要:

    为促进叠合剪力墙在装配式结构中的工程应用,提出一种新型带横肋双拼叠合剪力墙. 为探究横肋数量与边缘构件配箍率对该新型墙体受压承载力及延性的影响,首先,对3片带横肋双拼叠合剪力墙与1片现浇剪力墙开展轴心受压试验,分析试件的破坏形态与力学性能;其次,在试验验证的基础上建立精细化有限元模型,开展墙体受压性能的参数分析;最后,引入横肋影响系数与箍筋影响系数,通过非线性回归分析建立轴心受压承载力计算公式. 研究结果表明:带横肋双拼叠合剪力墙具有良好的整体性与塑性变形能力,平均峰值荷载达到现浇试件的93.12%,且在破坏前出现了较为明显的屈服阶段;采用等效刚度叠加法所得的墙体轴压弹性刚度为5272.42 kN/mm,与试验均值的误差仅为0.18%;随着预制墙板横肋数量从3个增至8个,墙体峰值承载力先降低后升高并在8个横肋时达最高值4996.76 kN,延性系数则先增大后减小并在6个横肋时达最大值2.009,适量横肋可以形成密集的约束网格以限制裂缝的扩展,而过多横肋会导致墙体破坏模式由界面剥离向整体压溃转变;经验证,所提承载力公式的计算值略低于试验值,偏于安全,平均误差仅为1.17%.

     

  • 图 1  带横肋双拼叠合剪力墙三维模型图

    Figure 1.  3D model of double-spliced composite shear wall with transverse ribs

    图 2  试件SPW1~SPW3几何尺寸及配筋

    Figure 2.  Geometric dimensions and reinforcement details of specimens SPW1-SPW3

    图 3  试件RCW几何尺寸及配筋

    Figure 3.  Geometric dimensions and reinforcement details of specimen RCW

    图 4  试件加载与位移计布置示意

    Figure 4.  Specimen loading setup and displacement gauge layout

    图 5  试件测点布置图

    Figure 5.  Measurement point layout for specimens

    图 6  试件RCW破坏形态

    Fig. 6 Failure mode of specimen RCW

    图 7  试件破坏形态

    Figure 7.  Failure mode of specimen

    图 8  试件竖向荷载-位移曲线

    Figure 8.  Vertical load-displacement curves of specimens

    图 9  试件抗剪箍筋荷载-应变曲线

    Figure 9.  Load-strain curves of shear reinforcement in specimens

    图 10  试件混凝土荷载-应变曲线

    Figure 10.  Load-strain curves of concrete in specimens

    图 11  有限元模型三维图

    Figure 11.  3D finite element model

    图 12  混凝土与钢筋间的粘结应力-滑移曲线

    Figure 12.  Bond stress-slip curve between concrete and reinforcing steel

    图 13  cohesive内聚力粘结模型曲线

    Figure 13.  Cohesive zone model curve

    图 14  试验与有限元计算荷载-位移曲线对比

    Figure 14.  Comparison of experimental and finite element load-displacement curves

    图 15  不同横肋数目下剪力墙荷载-位移曲线

    Figure 15.  Load-displacement curves of shear walls with different numbers of transverse ribs

    图 16  CH5与CH8试件在各特征点下的受拉损伤云图

    Figure 16.  Tensile damage contours of specimens CH5 and CH8 at characteristic load points

    图 17  $ n{\text{-}}\alpha $关系及其拟合曲线

    Figure 17.  $ n{\text{-}}\alpha $ relationship and fitted curve

    图 18  $ {\rho }_{v}{\text{-}}\beta $关系及其拟合曲线

    Figure 18.  $ {\rho }_{v}{\text{-}}\beta $ relationship and fitted curve

    表  1  钢筋实测强度值

    Table  1.   Measured strength values of reinforcing steel MPa

    钢筋直径/mm fy fu
    8 466.7 509.1
    16 425.7 529.2
    下载: 导出CSV

    表  2  混凝土实测平均强度值

    Table  2.   Measured mean compressive strength of concrete

    混凝土试块种类抗压强度/MPa
    现浇剪力墙40.97
    双拼叠合剪力墙现浇部分40.97
    双拼叠合剪力墙预制部分47.63
    下载: 导出CSV

    表  3  混凝土与钢筋间粘结应力-滑移曲线的参数值

    Table  3.   Parameters of bond stress-slip curve between concrete and reinforcing steel

    阶段 粘结应力/(N·mm−2) 相对滑移/mm
    劈裂(cr) $ {\tau }_{cr}=2.5{f}_{tr} $ $ {S}_{cr}=0.025d $
    峰值(u) $ {\tau }_{u}=3{f}_{tr} $ $ {S}_{u}=0.04d $
    残余(r) $ {\tau }_{r}={f}_{tr} $ $ {S}_{r}=0.55d $
    下载: 导出CSV

    表  4  不同横肋数目下带横肋双拼叠合剪力墙有限元计算结果

    Table  4.   Finite element analysis results for double-spliced composite shear walls with different numbers of transverse ribs

    加载阶段屈服点峰值点破坏点延性系数
    荷载/kN位移/mm荷载/kN位移/mm荷载/kN位移/mm
    预制墙板横肋数目/个34379.520.9864558.921.0863875.081.3911.411
    44339.210.9954553.741.1343870.101.4571.464
    54294.080.9984526.101.1623847.191.4881.492
    64117.050.9844493.831.2363819.451.9772.009
    74197.061.0584577.711.3863891.051.9211.816
    84463.141.2164996.761.6864247.251.9801.629
    下载: 导出CSV

    表  5  $ \alpha $分析结果

    Table  5.   Analysis results for transverse-rib influence factor $ \alpha $

    试件编号横肋数峰值承载力/kN$ \alpha $
    CH334558.921.039
    CH444553.741.038
    CH554526.101.030
    CH664493.831.021
    CH774577.711.044
    CH884996.761.160
    下载: 导出CSV

    表  6  $ \beta $分析结果

    Table  6.   Analysis results for stirrup influence factor $ \beta $

    试件编号 体积配箍率 峰值承载力/kN $ \beta $
    CSPW-1 0.31 4493.83 1.000
    CSPW-2 0.45 4523.34 1.008
    CSPW-3 0.60 4580.73 1.023
    CSPW-4 0.80 4577.96 1.022
    CSPW-5 0.94 4567.50 1.020
    CSPW-6 1.13 4601.28 1.029
    CSPW-7 1.25 4593.06 1.027
    CSPW-8 1.58 4636.98 1.039
    CSPW-9 1.79 4620.26 1.034
    CSPW-10 2.10 4648.57 1.042
    CSPW-11 2.39 4674.59 1.049
    CSPW-12 2.70 4717.04 1.060
    CSPW-13 3.03 4763.82 1.073
    CSPW-14 3.37 4760.41 1.072
    CSPW-15 3.74 4749.09 1.069
    下载: 导出CSV

    表  7  轴压承载力计算值与试验值对比

    Table  7.   Comparison of calculated and experimental axial compressive capacities

    试件编号试验值/kN计算值/kN差值/%
    SPW-14486.974481.980.11
    SPW-24619.434481.982.98
    SPW-34498.194481.980.36
    平均值4534.864481.981.17
    下载: 导出CSV
  • [1] 汪梦甫, 杨惠迪. 预制混凝土剪力墙结构体系的研究现状与改进策略[J]. 工程抗震与加固改造, 2020, 42(1): 1-9. doi: 10.16226/j.issn.1002-8412.2020.01.001

    Wang Mengfu, Yang Huidi. Research advance and improvement strategy of precast concrete shear wall structure system[J]. Earthquake Resistant Engineering and Retrofitting, 2020, 42(1): 1-9. doi: 10.16226/j.issn.1002-8412.2020.01.001
    [2] 李祚华, 田得元, 芦静夫, 等. 全装配式L形截面双面叠合剪力墙抗震性能试验研究[J]. 建筑结构学报, 2025, 46(1): 61-72. doi: 10.14006/j.jzjgxb.2024.0053

    Li Zuohua, Tian Deyuan, Lu Jingfu, et al. Experimental study on seismic behavior of fully assembled L-shaped section double-sided composite shear wall[J]. Journal of Building Structures, 2025, 46(1): 61-72. doi: 10.14006/j.jzjgxb.2024.0053
    [3] 李书蓉, 郭智远, 张鑫, 等. 预应力叠合剪力墙抗震性能研究[J]. 振动与冲击, 2025, 44(8): 220-227. doi: 10.13465/j.cnki.jvs.2025.08.024

    Li Shurong, Guo Zhiyuan, Zhang Xin, et al. Study on seismic behavior of prestressed concrete composite shear wall[J]. Journal of Vibration and Shock, 2025, 44(8): 220-227. doi: 10.13465/j.cnki.jvs.2025.08.024
    [4] 张鹏飞, 初明进, 钱增志, 等. 钢筋模板一体化剪力墙受弯性能试验研究[J]. 建筑结构学报, 2022, 43(3): 128-137. doi: 10.14006/j.jzjgxb.2019.0762

    Zhang Pengfei, Chu Mingjin, Qian Zengzhi, et al. Experimental study on flexural performance of integration of reinforcement and formwork shear walls[J]. Journal of Building Structures, 2022, 43(3): 128-137. doi: 10.14006/j.jzjgxb.2019.0762
    [5] 汪梦甫, 李柳红. 带钢板暗支撑叠合板式剪力墙恢复力模型研究[J]. 地震工程与工程振动, 2023, 43(3): 87-96. doi: 10.13197/j.eeed.2023.0309

    Wang Mengfu, Li Liuhong. Study on a hysteretic model of superimposed shear walls with steel plate concealed bracings[J]. Earthquake Engineering and Engineering Dynamics, 2023, 43(3): 87-96. doi: 10.13197/j.eeed.2023.0309
    [6] 常亚峰, 尹文哲, 侯亚鹏, 等. 超高性能混凝土预制板-叠合剪力墙抗震性能研究[J]. 地震工程与工程振动, 2024, 44(3): 96-107. doi: 10.13197/j.eeed.2024.0309

    Chang Yafeng, Yin Wenzhe, Hou Yapeng, et al. Study on seismic behavior of ultra-high performance concrete composite shear wall with precast slab[J]. Earthquake Engineering and Engineering Dynamics, 2024, 44(3): 96-107. doi: 10.13197/j.eeed.2024.0309
    [7] 熊焱, 赵国伟, 吴迪, 等. 自密实再生块体混凝土叠合剪力墙抗震性能试验研究[J]. 建筑结构学报, 2022, 43(4): 114-123, 133. doi: 10.14006/j.jzjgxb.2020.0472

    Xiong Yan, Zhao Guowei, Wu Di, et al. Experimental study on seismic behavior of composite shear walls filled with demolished concrete lumps and self-compacting concrete[J]. Journal of Building Structures, 2022, 43(4): 114-123,133. doi: 10.14006/j.jzjgxb.2020.0472
    [8] 郭延义, 朱安标, 赵欣. 钢板桁架双面叠合剪力墙及倒T板的制作及运输[J]. 建筑施工, 2022, 44(5): 942-945. doi: 10.14144/j.cnki.jzsg.2022.05.020

    Guo Yanyi, Zhu Anbiao, Zhao Xin. Fabrication and transportation of steel plate truss double-sided laminated shear wall and inverted T-plate[J]. Building Construction, 2022, 44(5): 942-945. doi: 10.14144/j.cnki.jzsg.2022.05.020
    [9] 龚祖平, 芮明倬, 李翔, 等. 模块化装配整体式自保温混凝土剪力墙力学性能分析[J]. 土木建筑工程信息技术, 2019, 11(6): 105-112. doi: 10.16670/j.cnki.cn11-5823/tu.2019.06.17

    Gong Zuping, Rui Mingzhuo, Li Xiang, et al. Analysis on mechanical performance of modular self-insulated prefabricated concrete shear wall[J]. Journal of Information Technology in Civil Engineering and Architecture, 2019, 11(6): 105-112. doi: 10.16670/j.cnki.cn11-5823/tu.2019.06.17
    [10] 林睿, 李振宝, 王文静, 等. 夹心保温双面叠合剪力墙受力性能研究进展[J]. 建筑结构, 2023, 53(11): 88-96, 142. doi: 10.19701/j.jzjg.20210094

    Lin Rui, Li Zhenbao, Wang Wenjing, et al. Research progress on mechanical behavior of double-superimposed shear wall with insulation[J]. Building Structure, 2023, 53(11): 88-96,142. doi: 10.19701/j.jzjg.20210094
    [11] 侯和涛, 叶海登, 马天翔, 等. 叠合整体式混凝土剪力墙轴心受压性能研究[J]. 建筑结构学报, 2016, 37(3): 76-85.

    Hou Hetao, Ye Haideng, Ma Tianxiang, et al. Study of integral composite reinforced concrete shear wall subjected to axial loading[J]. Journal of Building Structures, 2016, 37(3): 76-85.
    [12] 虞庐松, 刘彪, 王力, 等. 高寒环境温度下圆钢管混凝土短柱轴压性能试验研究[J]. 土木工程学报, 2023, 56(10): 20-31. doi: 10.15951/j.tmgcxb.22040426

    Yu Lusong, Liu Biao, Wang Li, et al. Experimental study on axial compression performance of CFST stub columns under very-cold ambient temperature[J]. China Civil Engineering Journal, 2023, 56(10): 20-31. doi: 10.15951/j.tmgcxb.22040426
    [13] 窦超, 杜彦珂, 杨潇. 可更换波折钢板剪切耗能型柱脚节点的滞回性能分析[J]. 天津大学学报(自然科学与工程技术版), 2024, 57(9): 935-946. doi: 10.11784/tdxbz202310023

    Dou Chao, Du Yanke, Yang Xiao. Hysteretic behavior of column base joints with replaceable shear corrugated plates[J]. Journal of Tianjin University, 2024, 57(9): 935-946. doi: 10.11784/tdxbz202310023
    [14] GB 50010—2010 混凝土结构设计规范[S].
    [15] Lee J, Fenves G L. Plastic-damage model for cyclic loading of concrete structures[J]. Journal of Engineering Mechanics, 1998, 124(8): 892-900. doi: 10.1061/(ASCE)0733-9399(1998)124:8(892)
    [16] 华昌昊, 方鑫, 顾冬生. 混凝土中灌浆套筒的本构模型研究[J]. 建筑结构, 2024, 54(18): 144-151, 143. doi: 10.19701/j.jzjg.20220281

    Hua Changhao, Fang Xin, Gu Dongsheng. Study on constitutive model of grouting sleeve in concrete[J]. Building Structure, 2024, 54(18): 144-151,143. doi: 10.19701/j.jzjg.20220281
    [17] 胡安龙, 尚志鹏, 薛国斌, 等. 局部预应力自复位装配式梁柱节点抗震性能参数影响分析[J]. 工程抗震与加固改造, 2025, 47(5): 62-71. doi: 10.16226/j.issn.1002-8412.2025.05.007

    Hu Anlong, Shang Zhipeng, Xue Guobin, et al. Analysis of parameter influence on seismic performance of partially prestressed self-centering precast beam-column joints[J]. Earthquake Resistant Engineering and Retrofitting, 2025, 47(5): 62-71. doi: 10.16226/j.issn.1002-8412.2025.05.007
    [18] 蔡忠奎, 苑溦, 路广, 等. 用于混合配筋节段拼装桥墩抗震设计的骨架曲线模型分析[J]. 建筑科学, 2024, 40(11): 140-150. doi: 10.13614/j.cnki.11-1962/tu.2024.11.017

    Cai Zhongkui, Yuan (Mei| Wei), Lu Guang, et al. Analysis of skeleton curve model used for seismic design of hybrid reinforced precast segmental bridge column[J]. Building Science, 2024, 40(11): 140-150. doi: 10.13614/j.cnki.11-1962/tu.2024.11.017
    [19] ACI Committee 318. Building Code Requirements for Structural Concrete (ACI 318-11) and Commentary[M]. Farmington Hills: American Concrete Institute, 2014.
    [20] 王振领. 新老混凝土粘结理论与试验及在桥梁加固工程中的应用研究[D]. 成都: 西南交通大学, 2007.
    [21] 刘健. 新老混凝土粘结的力学性能研究[D]. 大连: 大连理工大学, 2000.
    [22] 周剑. 预制混凝土空心模剪力墙应用技术研究[D]. 北京: 清华大学, 2015.
  • 加载中
图(18) / 表(7)
计量
  • 文章访问数:  3
  • HTML全文浏览量:  4
  • PDF下载量:  1
  • 被引次数: 0
出版历程
  • 收稿日期:  2025-06-13
  • 修回日期:  2026-04-14
  • 网络出版日期:  2026-11-17

目录

    /

    返回文章
    返回