Vehicle Dynamic Response Analysis of Heavy Haul Freight Cars under Braking Conditions
-
摘要:
随着我国重载铁路的发展,重载货车轴重增加且编组加长,重载车辆在制动工况下,车间相互作用和轮轨相互作用更加剧烈,恶化车辆动力学性能,需要进一步研究重载货车制动工况下的动力学响应. 本文建立了考虑闸瓦制动子模型的重载货车动力学模型,并利用实测数据验证了模型的有效性. 并分析了重载货车在正常制动、紧急制动和间接制动下的轮轨接触特性以及车辆安全性指标. 结果表明:在制动工况下,其垂向轮轨力以及轮轨间的蠕滑率都会增大. 而在车辆通过曲线路段时施加制动力,会导致车辆的轮重减载率与脱轨系数上升,在600 m半径处,纵向蠕滑率与纵向蠕滑力分别达到了正常制动的1.5倍与1.8倍. 同时车辆在长大下坡进行间接制动也同样会对车辆动力学性能造成影响,相比于惰行工况,制动工况下垂向轮轨力增大了8 kN左右,引起一位轮对产生剧烈振动. 长大下坡制动时的工况的安全性指标略高. 当存在轮径差时,制动工况轮轨响应更加剧烈. 当轮径差值从1 mm增大至5 mm时,紧急制动下的垂向轮轨力从135.8 kN增加到了142.6 kN增大了6.1%,横向力与脱轨系数分别增加了163%与139%. 紧急制动下,动力学响应更加剧烈;长大坡道时,间接制动下动力学会对动力学造成影响,当存在轮径差时,动力学指标进一步增大.
Abstract:With the development of heavy haul railways in China, the axle load of heavy haul freight cars has increased, and the train formation has become longer. The interactions between vehicles and the wheel-rail become more intense during the braking conditions of heavy haul cars, which deteriorates the vehicle dynamics performance. It is necessary to further study the dynamic response of heavy haul freight cars under braking conditions. A dynamic model of heavy haul freight cars considering the brake shoe braking sub-model. The effectiveness of the model was verified with measured data. The wheel-rail contact characteristics and vehicle safety indexes under normal braking, emergency braking, and indirect braking of heavy haul freight were analyzed. The results show that under braking conditions, both the vertical wheel-rail force and the creepage between the wheel and rail increase. When braking force is applied while the vehicle passes through a curved track, both the wheel unloading rate and the derailment coefficient increase consequently. With a radius of 600 m, the longitudinal creepage and longitudinal creep force reach 1.5 and 1.8 times those of normal braking, respectively. At the same time, indirect braking on long downhill slopes will also affect the dynamic performance of the vehicle. Compared with the idle operation condition, the vertical wheel-rail force rises by about 8 kN during braking conditions, causing the first wheelsets to produce severe vibration. The safety indexes of the braking condition on long downhill slopes are slightly higher. When there is a wheel diameter difference, the wheel-rail response under braking conditions is more intense. When the wheel diameter difference increases from 1 mm to 5 mm, the vertical wheel-rail force under emergency braking grows from 135.8 to 142.6 kN, an increase of 6.1%, and the lateral force and derailment coefficient go up by 163% and 139%, respectively. The dynamic response is more intense under emergency braking. On long slopes, indirect braking will affect the dynamics. When there is a wheel diameter difference, the dynamic indicators further increase.
-
表 1 车辆主要结构参数
Table 1. Main structural parameters of vehicle
参数 值 参数 值 轮对质量/kg 1171 轮对沿z轴转动惯量/(kg•m2) 700 侧架质量/kg 497 轮对沿y轴转动惯量/(kg•m2) 72 车体质量
(空车)/kg10829 侧架沿y轴转动惯量/(kg•m2) 188.2 车轮名义滚动圆半径/m 0.42 侧架沿z轴转动惯量/(kg•m2) 172.5 车体沿x轴转动惯量/(kg•m2) 6.932 × 104 轮对沿x轴转动惯量/(kg•m2) 700 车体沿y轴转动惯量/(kg•m2) 1.837 × 105 转向架轴距/m 1.83 车体沿z轴转动惯量/(kg•m2) 2.127 × 105 车辆定距/m 8.2 侧架沿x轴转动惯量/(kg•m2) 20.735 表 2 闸瓦制动力计算主要参数
Table 2. Main parameters of brake shoe braking force calculation
符号 含义 数值 $ {{d}}_{{\textit{z}}} $ 制动缸直径/mm 305 ${{p}}_{{\textit{z}}} $ 制动缸压力/kN $ {\eta }_{{\textit{z}}} $ 传动效率 0.9 $ {\gamma }_{{\textit{z}}} $ 制动倍率 8.5 $ {n}_{{\textit{z}}} $ 制动缸数 1 $ {n}_{k} $ 闸瓦数 1 表 3 曲线路况
Table 3. Curved road conditions
曲线半径/m 曲线超高/mm 直线段长度/m 缓和曲线/m 圆曲线/m 600 70 200 200 600 800 55 200 200 600 1000 45 200 200 600 1200 35 200 200 600 -
[1] 李中奇, 余剑烽, 周靓. 重载列车运行过程的滑模自抗扰控制方法[J]. 西南交通大学学报, 2026, 61(1): 197-206, 242. doi: 10.3969/j.issn.0258-2724.20240120Li Zhongqi, Yu Jianfeng, Zhou Liang. Sliding mode active disturbance rejection control method for heavy-haul trains during operation[J]. Journal of Southwest Jiaotong University, 2026, 61(1): 197-206,242. doi: 10.3969/j.issn.0258-2724.20240120 [2] Sui S Q, Wang K Y, Ling L, et al. Effect of wheel diameter difference on tread wear of freight wagons[J]. Engineering Failure Analysis, 2021, 127: 105501. doi: 10.1016/j.engfailanal.2021.105501 [3] 周高伟, 高飞, 段军军. 超长大坡道持续制动条件下列车车轮踏面温度分布的试验研究[J/OL]. 西南交通大学学报, 1-8[2024-12-26].Zhou Gaowei, Gao Fei, Duan Junjun. Experimental study on temperature distribution of wheel tread undelcontinuous braking on super-long ramp[J]. Journal of Southwest Jiaotong University, 1-8[2024-12-26]. [4] Liu P F, Wang K Y. Effect of braking operation on wheel–rail dynamic interaction of wagons in sharp curve[J]. Proceedings of the Institution of Mechanical Engineers, Part K: Journal of Multi-body Dynamics, 2017, 231(1): 252-265. doi: 10.1177/1464419316662182 [5] Sun Y Q, Ahmad S N, Persson I, et al. Freight container wagon modelling and simulation analysis due to braking[J]. Vehicle System Dynamics, 2024, 62(12): 3255-3275. doi: 10.1080/00423114.2024.2325189 [6] Micheale Yihdego Gebreyohanes, 莫继良, 楚明, 等. 制动条件下高速列车轮轨动态响应特性分析[J]. 重庆理工大学学报(自然科学), 2022, 36(12): 289-296.Gebreyohanes M Y, Mo Jiliang, Chu Ming, et al. Investigation of dynamic wheel-rail response characteristics of a high-speed train under braking conditions[J]. Journal of Chongqing University of Technology (Natural Science), 2022, 36(12): 289-296. [7] 黎启玄. 制动系统特性对重载列车纵向动力学性能影响仿真研究[D]. 大连: 大连交通大学, 2023.Li Qixuan. Simulation research on the influence of braking system characteristics on the longitudinal dynamic performance of heavy haul train[D]. Dalian: Dalian Jiaotong University, 2023. [8] Corrêa P H A, Ramos P G, Teixeira L H S, et al. Dynamic simulation of a heavy-haul freight car under abnormal braking application on tangent and curve[J]. Vehicle System Dynamics, 2023, 61(9): 2456-2471. doi: 10.1080/00423114.2022.2113807 [9] 李志强, 郑轶男, 张晓康, 等. 制动工况对高速列车制动盘残余应力及翘曲变形的影响[J]. 西南交通大学学报, 2025, 60(5): 1278-1286. doi: 10.3969/j.issn.0258-2724.20230691Li Zhiqiang, Zheng Yinan, Zhang Xiaokang, et al. Influence of braking conditions on residual stress and warping deformation of brake discs of high-speed trains[J]. Journal of Southwest Jiaotong University, 2025, 60(5): 1278-1286. doi: 10.3969/j.issn.0258-2724.20230691 [10] 李亨利, 李芾, 傅茂海, 等. 曲线几何参数对货车转向架曲线通过性能的影响[J]. 中国铁道科学, 2008, 29(1): 70-75. doi: 10.3321/j.issn:1001-4632.2008.01.015Li Hengli, Li Fu, Fu Maohai, et al. Influence of curve geometric parameters on the curve negotiation performance of freight car bogies[J]. China Railway Science, 2008, 29(1): 70-75. doi: 10.3321/j.issn:1001-4632.2008.01.015 [11] 祁亚运, 张文谦, 张良威, 等. 制动工况下重载货车车轮扁疤对轮轨振动响应分析[J]. 振动与冲击, 2024, 43(8): 119-126, 154. doi: 10.13465/j.cnki.jvs.2024.08.013Qi Yayun, Zhang Wenqian, Zhang Liangwei, et al. Analysis of wheel rail vibration response caused by wheel flat of heavy freight vehicles under braking conditions[J]. Journal of Vibration and Shock, 2024, 43(8): 119-126,154. doi: 10.13465/j.cnki.jvs.2024.08.013 [12] 刘开忠, 王志伟, 张卫华. 紧急制动条件下重载货车车辆动力学行为研究[J]. 振动工程学报, 2025, 38(2): 365-374. doi: 10.16385/j.cnki.issn.1004-4523.2025.02.015Liu Kaizhong, Wang Zhiwei, Zhang Weihua. Vehicle dynamics behavior of heavy-haul wagon vehicle under emergency braking conditions[J]. Journal of Vibration Engineering, 2025, 38(2): 365-374. doi: 10.16385/j.cnki.issn.1004-4523.2025.02.015 [13] 王宇嘉, 徐利民, 贾永刚, 等. 山西中南部通道重载列车运输试验及对线路设计的启示[J]. 铁道货运, 2015, 33(10): 27-31, 41. doi: 10.16669/j.cnki.issn.1004-2024.2015.10.07 [14] 张家梁, 付茂海, 刘思达, 等. 长大坡道对货物列车纵向动力学特性的影响研究[J]. 机械工程与自动化, 2022, 51(2): 33-35. doi: 10.3969/j.issn.1672-6413.2022.02.011Zhang Jialiang, Fu Maohai, Liu Sida, et al. Study on influence of long ramp on longitudinal dynamic characteristics of freight train[J]. Mechanical Engineering & Automation, 2022, 51(2): 33-35. doi: 10.3969/j.issn.1672-6413.2022.02.011 [15] 温登钦, 王飞, 时瑾, 等. 重载铁路长大下坡曲线段列车行车安全性分析[J]. 中国安全科学学报, 2022, 32(6): 87-94. doi: 10.16265/j.cnki.issn1003-3033.2022.06.1896Wen Dengqin, Wang Fei, Shi Jin, et al. Safety analysis of train operation in long downhill curve sections of heavy haul railways[J]. China Safety Science Journal, 2022, 32(6): 87-94. doi: 10.16265/j.cnki.issn1003-3033.2022.06.1896 [16] 杨春雷, 黄运华, 丁军君. 重载轨道曲线几何参数对轮轨耦合动力特性的影响[J]. 交通运输工程学报, 2021, 21(3): 215-227. doi: 10.19818/j.cnki.1671-1637.2021.03.014Yang Chunlei, Huang Yunhua, Ding Junjun. Influences of curve geometric parameters of heavy haul track on wheel/rail coupling dynamic characteristics[J]. Journal of Traffic and Transportation Engineering, 2021, 21(3): 215-227. doi: 10.19818/j.cnki.1671-1637.2021.03.014 [17] 周坤, 王彦, 杨麦生, 等. 40 t轴重重载铁路曲线超高对行车性能的影响规律分析[J]. 铁道标准设计, 2021, 65(9): 56-61. doi: 10.13238/j.issn.1004-2954.202006150001Zhou Kun, Wang Yan, Yang Maisheng, et al. Analysis of influence of curve superelevation on running performance of 40 t axle load heavy haul railway[J]. Railway Standard Design, 2021, 65(9): 56-61. doi: 10.13238/j.issn.1004-2954.202006150001 [18] 国家铁路局. 列车牵引计算第1部分: 机车牵引式列车现行: TB/T 1407.1-2018 [S]. 北京: 中国标准出版社, 2018. [19] 李亨利, 李芾, 付茂海, 等. 重载货车坡道制动动力学及轮轨磨耗研究[J]. 铁道科学与工程学报, 2014, 11(3): 60-64. doi: 10.3969/j.issn.1672-7029.2014.03.010Li Hengli, Li Fei|, Fu Maohai, et al. Study on the braking dyna mics and wheel/rail wear for the heavy haul trucks on ramp lines[J]. Journal of Railway Science and Engineering, 2014, 11(3): 60-64. doi: 10.3969/j.issn.1672-7029.2014.03.010 [20] 国家标准局. 铁道车辆动力学性能评定和实验鉴定规范: GB5599-2019 [S]. 北京: 中国标准出版社, 2019. [21] 池茂儒, 张卫华, 曾京, 等. 轮径差对行车安全性的影响[J]. 交通运输工程学报, 2008, 8(5): 19-22. doi: 10.3321/j.issn:1671-1637.2008.05.004Chi Maoru, Zhang Weihua, Zeng Jing, et al. Influence of wheel-diameter difference on running security of vehicle system[J]. Journal of Traffic and Transportation Engineering, 2008, 8(5): 19-22. doi: 10.3321/j.issn:1671-1637.2008.05.004 [22] 祁亚运, 戴焕云, 干锋, 等. 高速动车组车轮偏磨影响因素与限值研究[J]. 表面技术, 2023, 52(5): 51-60. doi: 10.16490/j.cnki.issn.1001-3660.2023.05.005Qi Yayun, Dai Huanyun, Gan Feng, et al. Influencing factors and limits of asymmetrical wheel wear of high-speed EMUs[J]. Surface Technology, 2023, 52(5): 51-60. doi: 10.16490/j.cnki.issn.1001-3660.2023.05.005 [23] 祁亚运, 戴焕云, 高浩, 等. 考虑驱动系统的高速列车动力学分析[J]. 振动工程学报, 2019, 32(1): 176-183. doi: 10.16385/j.cnki.issn.1004-4523.2019.01.020Qi Yayun, Dai Huanyun, Gao Hao, et al. Dynamic analysis of high-speed train with considering drive system[J]. Journal of Vibration Engineering, 2019, 32(1): 176-183. doi: 10.16385/j.cnki.issn.1004-4523.2019.01.020 -
下载: