基于喷丸随机模型的表面覆盖率计算方法

强斌; 李亚东; 顾颖; 倪金荣

doi:10.3969/j.issn.0258-2724.2016.06.018

基于喷丸随机模型的表面覆盖率计算方法

doi: 10.3969/j.issn.0258-2724.2016.06.018

强斌¹,
李亚东^1, ,,
顾颖¹,
倪金荣²

基金项目:

国家自然科学基金资助项目（51378430）

详细信息

作者简介:
强斌(1987-),男,博士研究生,研究方向为钢桥焊接的应力与变形控制,E-mail:binqiang1987@163.com

通讯作者:
李亚东(1956-),男,教授,博士生导师,研究方向为桥梁设计理论与施工控制、钢桥稳定与疲劳等,E-mail:ydli@swjtu.cn

计量
- 文章访问数: 605
- HTML全文浏览量: 118
- PDF下载量: 176
- 被引次数: 0
出版历程
- 收稿日期: 2015-07-13
- 刊出日期: 2016-12-25

Calculation Method of Surface Coverage Based on Shot Peening Random Model

摘要

摘要: 为了揭示金属结构表面喷丸处理过程中覆盖率的变化规律，通过分析喷丸随机模型的建模流程及靶材的喷丸后形貌，利用MATLAB软件开发了基于喷丸随机模型的覆盖率计算程序，并将此与传统覆盖率计算方法进行了对比.结果表明：以直径为1.0 mm，速率为50 m/s的弹丸对构件进行喷丸处理，当弹丸数目N20时，新方法（MATLAB法）与传统方法（PEEQ法和理论公式法）的计算结果较接近；随着弹丸数目的增加，在达到全覆盖之前，3种方法的计算覆盖率为CPEEQ Cth CMATLAB；全覆盖时，3种方法所对应的弹丸数目分别为100、140和190.
- 喷丸 /
- 表面覆盖率 /
- 随机模型 /
- MATLAB程序 /
- 计算方法
Abstract: To reveal the coverage variation in shot peening process for metal structure, a MATLAB program was designed to calculate the coverage by analyzing the modeling process of shot peening random model and target morphology after shot peening. Also, the developed method was compared with the traditional coverage calculation methods. The comparison shows that, with shot diameter of 1 mm and velocity of 50 m/s, when the shot number N is less than 20, the results from the developed coverage calculation (MATLAB method) are approximate to those from the traditional methods (PEEQ method and theoretical formula method). With the increase of shot number, it shows CPEEQ Cth CMATLAB before reaching full coverage. When there is full coverage, the shot numbers corresponding to three methods are 100, 140 and 190, respectively.
- shot peening /
- surface coverage /
- random model /
- MATLAB program /
- calculation method

HTML全文

参考文献(16)

BAGHERIFARD S, GHELICHI R, GUAGLIANO M. Numerical and experimental analysis of surface roughness generated by shot peening[J]. Applied Surface Science, 2012, 258:6831-6840.

KLEMENZ M, SCHULZE V, ROHR I, et al. Application of the FEM for the prediction of the surface layer characteristics after shot peening[J]. Journal of Materials Processing Technology, 2009, 209:4093-4102.

BAGHERIFARD S, GHELICHI R, GUAGLIANO M. A numerical model of severe shot peening(SSP) to predict the generation of a nanostructured surface layer of material[J]. Surface and Coatings Technology, 2010, 204:4081-4090.

HONG T, OOI J Y, SHAW B. A numerical simulation to relate the shot peening parameters to the induced residual stresses[J]. Engineering Failure Analysis, 2008, 15:1097-1110.

BAGHERIFARD S, GHELICHI R, GUAGLIANO M. On the shot peening surface coverage and its assessment by means of finite element simulation:a critical review and some original developments[J]. Applied Surface Science, 2012, 259:186-194.

KIRK D, ABYANEH M Y. Theoretical basis of shot peening coverage control[J]. The Shot Peener,1993,2(9):28-30.

KIRK D, ABYANEH M Y. Theoretical basis of shot peening coverage control[J]. The Shot Peener, 1995, 9(2):28-30.

KIRK D, ABYANEH M Y. Theoretical basis of shot peening coverage control[J]. The Shot Peener, 1999,13(3):5-7.

KARUPPANAN S, ROMERO J S, DELOS E R, et al. A theoretical and experimental investigation into the development of coverage in shot peening[C]//Proceedings of the 8th International Conference on Shot Peening. Garmisch-Partenkirchen:, 2002:101-107.

MIAO H Y, LAROSE S, PERRON C, et al. On the potential applications of a 3D random finite element model for the simulation of shot peening[J]. Advances in Engineering Software, 2009, 40:1023-1038.

MEGUID S A, SHAGAL G, STRANART J C. 3D FE analysis peening of strain-rate sensitive materials using mul-tiple impingement model[J]. International Journal of Impact Engineering, 2002, 27(2):119-134.

张洪伟,张以都,吴琼. 喷丸强化残余应力场三维数值分析[J]. 航空动力学报,2010,25(3):603-609. ZHANG Hongwei, ZHANG Yidu, WU Qiong. Three-dimensional numerical analysis of residualstress field for shot-peening[J]. Journal of Aerospace Power, 2010, 25(3):603-609.

强斌,李亚东,顾颖,等. 钢板喷丸处理残余应力场和表面粗糙度数值模拟[J]. 西南交通大学学报,2015,50(4):691-697. QIANG Bin, LI Yadong, GU Ying, et al. Numerical simulation of residual stress field and surface roughness for steel plate subjected to shot peening[J]. Journal of Southwest Jiaotong University, 2015, 50(4):691-697.

于文静,史健勇,赵金城. Q345钢材动态力学性能研究[J]. 建筑结构,2011,41(3):28-30. YU Wenjing, SHI Jianyong, ZHAO Jincheng. Research of dynamic mechanical behavior of Q345 steel[J]. Building Structure, 2011, 41(3):28-30.

秦襄培, 郑贤中. MATLAB图像处理宝典[M]. 北京:电子工业出版社,2011:79-106.

PEDRO S, CRISTINA R. Influence of the target material constitutive model on the numerical simulation of a shot peening process[J]. Surface and Coatings Technology, 2014, 258:822-831.

施引文献

附加材料(0)

访问统计