基于容腔调节的钢轨打磨压力控制系统

聂蒙; 李建勇; 沈海阔

doi:10.3969/j.issn.0258-2724.2015.05.005

基于容腔调节的钢轨打磨压力控制系统

doi: 10.3969/j.issn.0258-2724.2015.05.005

基金项目:

中央高校基本科研业务费专项资金资助项目(M14JB00010)

详细信息

通讯作者:
李建勇(1962-),男,教授,博士,研究方向为先进制造技术,E-mail:jyli@bjtu.edu.cn

计量
- 文章访问数: 762
- HTML全文浏览量: 73
- PDF下载量: 443
- 被引次数: 0
出版历程
- 收稿日期: 2013-06-14
- 刊出日期: 2015-10-25

Pressure Control System for Rail Grinding Based on Chamber Adjustment

摘要

摘要: 为了降低钢轨打磨过程中的压力波动,采用在传统气动恒压控制系统中加入容腔调节器的方法构建新型钢轨打磨压力控制系统.容腔调节器由储气罐与比例流量阀构成,能够在系统受到压力冲击时吸收冲击压力,降低压力波动,并在系统需要输出压力时补充系统供能,加速系统响应.为了保障钢轨打磨控制的精确性与稳定性,所研究的钢轨打磨压力系统采用了双闭环的形式,以变结构控制为基础,结合每个闭环的控制特性来构建控制器.为了验证所提出控制系统的特性,分别以系统仿真与打磨实验的形式与传统钢轨打磨压力控制系统进行对比.结果显示,与传统系统相比,本文所提出的容腔调节控制系统控制压力波动降低了76.8%.
- 钢轨打磨 /
- 容腔调节器 /
- 气动压力控制 /
- 变结构控制
Abstract: To reduce the pressure fluctuation during rail grinding operation, a new rail grinding pressure control system was proposed by adding a chamber adjuster into the traditional pneumatic constant pressure control system. The chamber adjuster consisted of a gas holder and a proportional flow valve. It could absorb the shock pressure exerting on the system to reduce the pressure fluctuation and supplement energy for the system when delivery pressure was needed to accelerate system response. To ensure the accuracy and stability of the rail grinding pressure control, the rail grinding pressure system with chamber adjuster adopted a double closed-loop control system based on variable structure control, and the controller was designed according to the control characteristic of each closed loop. In addition, the characteristics of the proposed control system were verified by numerical simulation and grinding experiments, and compared with those of the traditional rail grinding pressure control system. The results show that the chamber adjustment control system could reduce 76.8% of the pressure fluctuation in the traditional pressure control system.
- rail grinding /
- chamber adjuster /
- pneumatic pressure control /
- variable structure control

HTML全文

参考文献(47)

金学松,杜星,郭俊,等. 钢轨打磨技术研究进展

魏长竹,魏晨. 钢轨打磨车磨头数量及驱动方式分析

[J]. 西南交通大学学报,2010,45(1): 7-11. JIN Xuesong, DU Xing, GUO Jun, et al. State of arts of research on rail grinding

张建峰,高新平,王卫东,等. 重载铁路钢轨打磨效果分析

[J]. Journal of Southwest Jiaotong University, 2010, 45(1): 7-11.

方立志,胡军科,周乾刚,等, 钢轨打磨车恒力加载系统的分析仿真研究

[J]. 城市轨道交通研究,2010,13(12): 85-88. WEI Changzhu, WEI Chen. Analysis on the gringing wheel quantity and the drive mode of rail gringing vehicle

NORITSUGU T, TAKAIWA M. Robust positioning control of pneumatic servo system with pressure control loop

PANDIAN S, TAKEMURA R. Pressure observer controller design for pneumatic cylinder actuators

[J]. Urban Mass Transit, 2010, 13(12): 85-88.

刘忠,龙国键,褚福磊,等. 基于高速开关电磁阀技术的压力控制系统设计

[J]. 铁道建筑,2009(4): 104-105. ZHANG Jianfeng, GAO Xingping, WANG Weidong, et al. Analysis of heavy railway grinding effect

王雪松,程玉虎,彭光正. 电气比例阀自校正压力调节器的设计

[J]. Railway Engineering, 2009(4): 104-105.

车彦东,彭光正,钟圣国. 气动压力控制系统自校正控制的实用化研究

李宝仁,刘浩,傅晓云,等. 密闭容腔压力伺服控制系统理论与实验研究

[J]. 铁道科学与工程学报,2012,9(2): 115-118. FANG Lizhi, HU Junke, ZHOU Qiangang, et al. Analysis and simulation of the constant loading system of rail grinding train

聂蒙,李建勇,沈海阔,等. 钢轨打磨压力波动的影响机理

TAO Guoliang, WANG Xuanyin.The reaearch on electro-pneumatic-servo robot writing chinese calligraphy

[J]. Journal of Railway Science and Engineering, 2012, 9(2): 115-118.

SANVILLE F E. A new method of specifying the flow capacity of pneumatic fluid power valves

陶国良,王宣银,路甬祥,等. 3自由度气动比例/伺服机械手连续轨迹控制的研究

[C]//IEEE International Conference on Robotics and Automation. Okayama:

朱春波,包钢,聂伯勋,等. 用于气动伺服系统的自适应神经模糊控制器

[s. n.], 1995: 2613-2618.

周跃清,田常海,张银花,等. 高速铁路钢轨打磨关键技术研究

[J]. IEEE/ASME Transactions on Mechatronics, 2002, 7(4): 490-499.

[J]. 液压与气动,2003(3): 13-15. LIU Zhong, LONG Guojian, CHU Fulei, et al. The research of the pressure control system based on high-speed on-off valve

[J]. Chinese Hydraulics Pneumatics, 2003(3): 13-15.

[J]. 电机与控制学报,2006,10(1): 27-29. WANG Xuesong, CHENG Yuhu, PENG Guangzheng. A proposal of self-tunning pressure regulator for electro-pneumatic proportional pressure valve

[J]. Electric Machines and Control, 2006, 10(1): 27-29.

[J]. 机床与液压,2006(7): 143-144. CHE Yandong, PENG Guangzheng, ZHONG Shengguo. Application research of self-tuning technology in pneumatic pressure control system

[J]. Machine Tool Hydraulics, 2006(7): 143-144.

[J]. 液压与气动,2004(7): 1-3. LI Baoren, LIU Hao, FU Xiaoyun, et al. Theoretical and experimental research on pressure servo control system of closed chamber

[J]. Chinese Hydraulics Pneumatics, 2004(7): 1-3.

[J]. 中南大学学报:自然科学版,2013,44(8): 3576-3551. NIE Meng,LI Jianyong, SHEN Haikuo, et al. Grinding pressure fluctuation of rail grinding

[J]. Journal of Central South University: Science and Technology, 2013, 44(8): 3576-3551.

[C]//2nd Internationals' Fluid Technisches. Dresden:

[s. n.], 2000: 4-16.

[C]//Second Fluid power Symposium.

[S. 1.]: BHRA, 1997: 37-47.

[J]. 机械工程学报,2001,37(3): 65-69. TAO Guoliang, WANG Xuanyin, LU Yongxiang, et al. Research on the continuous trajectory tracking control to pneumatic-servo robot with three-degree-of freedom

[J]. Journal of Mechanical Engineering, 2001, 37(3): 65-69.

[J]. 机械工程学报,2001,37(10): 79-82. ZHU Chunbo, BAO Gang, NIE Boxun, et al. Adaptive neural network fuzzy controller for pneumatic servo system

[J]. Journal of Mechanical Engineering, 2001, 37(10): 79-82.

[J]. 中国铁道科学,2012,33(2): 66-69. ZHOU Yueqing, TIAN Changhai, ZHANG Yinhua, et al. Research on key rail gringing technology of high-speed railway

[J]. China Railway Science, 2012, 33(2): 66-69.

施引文献

附加材料(0)

访问统计