钢板喷丸处理残余应力场和表面粗糙度数值模拟

强斌; 李亚东; 顾颖; 杨元录

doi:10.3969/j.issn.0258-2724.2015.04.018

钢板喷丸处理残余应力场和表面粗糙度数值模拟

doi: 10.3969/j.issn.0258-2724.2015.04.018

强斌¹,
李亚东^1, ,,
顾颖¹,
杨元录²

基金项目:

国家自然科学基金资助项目(51378430)

中央高校基本科研业务费专项资金科技创新项目(SWJTU11CX005)

详细信息

作者简介:
强斌(1987-),男,博士研究生,研究方向为钢桥焊接的应力与变形控制,E-mail:binqiang1987@163.com

通讯作者:
李亚东(1956-),男,教授,博士生导师,研究方向为桥梁设计理论与施工控制、钢桥稳定与疲劳等,E-mail:ydli@swjtu.cn

计量
- 文章访问数: 1112
- HTML全文浏览量: 76
- PDF下载量: 506
- 被引次数: 0
出版历程
- 收稿日期: 2014-09-15
- 刊出日期: 2015-08-25

Numerical Simulation of Residual Stress Field and Surface Roughness for Steel Plate Subjected to Shot Peening

摘要

摘要: 为了揭示钢板喷丸处理后残余应力场以及表面粗糙度的分布规律,采用有限元软件ABAQUS建立了多丸模型,模拟了铸铁丸对桥梁用钢Q345钢板的喷射过程,对比分析了冲击速度、冲击次数和弹丸直径对喷丸后钢板水平向残余应力沿板厚的分布以及表面粗糙度的影响.研究结果表明,随着冲击速度、冲击次数以及弹丸直径的增加,残余压应力有均匀化的趋势,并且分布范围逐渐向厚度方向发展,同时表面粗糙度也随之逐渐增大.根据表面粗糙度随冲击次数的变化规律,建议采用对数函数来表示二者的关系,并给出了弹丸直径为1.4 mm情况下表面粗糙度值与喷丸速度和冲击次数的相互关系.
- 桥梁用钢 /
- 喷丸 /
- 数值模拟 /
- 残余应力 /
- 表面粗糙度
Abstract: In order to study the distribution of residual stress field and surface roughness of a steel plate after shot peening treatment, finite element models of shot peening with multiple shots are established using ABAQUS. Through the models, the dynamic process of cast shot peening of Q345 steel plates used for bridge is simulated. Moreover, the effect of impact velocity, impact times, and shot diameter on the horizontal residual stress along the depth and on the surface roughness are analyzed. The results show that as the impact velocity, impact times, and shot diameter increase, the residual compressive stress has a trend of homogenization, the stress distribution range develops gradually in the direction of thickness, and the surface roughness increases gradually. According to the law of surface roughness changing with the impact times, a logarithmic function is proposed to represent the relationship between surface roughness and impact times. In addition, given a shot diameter of 1.4 mm, the relationship between surface roughness, impact velocity and impact times is presented.
- bridge steel /
- shot peening /
- numerical simulation /
- residual stress /
- surface roughness

HTML全文

参考文献(35)

王仁智. 金属材料的喷丸强化原理及其强化机理综述

[J]. 中国表面工程,2012,25(6): 1-8. WANG Renzhi. Overview on the shot peening principle and its strengshening mechanisms for metallic materials

李雁淮,王飞,吕坚,等. 单丸粒喷丸模型和多丸粒喷丸模型的有限元模拟

凌祥,彭薇薇,倪红芳. 喷丸三维残余应力场的有限元模拟

[J]. China Surface Engineering, 2012, 25(6): 1-8.

HONG T, OOI J Y, SHAW B. A numerical simulation to relate the shot peening parameters to the induced residual stresses

[J]. 西安交通大学学报,2007,41(3): 348-352. LI Yanhuai, WANG Fei, LV Jian, et al. Finite element analysis for shot-peening models of single shot impact and multiple impingement

MEO M, VIGNJEVIC R. Finite element analysis of residual stress induced by shot peening process

MEGUID S A, SHAGAL G, STRANART J C J, et al. Three-dimensional dynamic finite element analysis of shot-peening induced residual stresses

[J]. Journal of Xi'an Jiaotong University, 2007, 41(3): 348-352.

MAJZOOBI G H, AZIZI R, NIA A. A three-dimensional simulation of shot peening process using multiple shot impacts

[J]. 机械工程学报,2006,42(8): 182-189. LING Xiang, PENG Weiwei, NI Hongfang. Simulation of 3D residual stress field of shot peening by dynamic finite element analysis

KIM T, LEE J H, LEE H, et al. An area-average approach to peening residual stress under multi-impacts using a three-dimensional symmetry-cell finite element model with plastic shots

[J]. Chinese Journal of Mechanical Engineering, 2006, 42(8): 182-189.

MIAO H Y, LAROSE S, PERRON C, et al. On the potential applications of a 3D random finite element model for the simulation of shot peening

张洪伟,陈家庆,张以都. 基于多丸粒模型的喷丸表面强化过程数值模拟

MEGUID S A, SHAGAL G, STRANART J C. 3D FE analysis peening of strain-rate sensitive materials using mul-tiple impingement model

[J]. Engineering Failure Analysis, 2008, 15: 1097-1110.

MEGUID S A, SHAGAL G, STRANART J C. Three-dimensional dynamic finite element analysis of shot-peening induced residual stresses

[J]. Advances in Engineering Software, 2003, 34: 569-575.

于文静,史健勇,赵金城. Q345钢材动态力学性能研究

中华人民共和国铁道部. TB/T 15272011铁路钢桥保护涂装及涂料供货技术条件

中华人民共和国交通部. JT/T 7222008公路桥梁钢结构防腐涂装技术条件

[J]. Finite Elements in Analysis and Design, 1999, 31: 179-191.

[J]. Journal of Materials Processing Technology, 2005, 164/165: 1226-1234.

[J]. Materials and Design, 2010, 31: 50-59.

[J]. Advances in Engineering Software, 2009, 40: 1023-1038.

[J]. 塑性工程学报,2012,19(6): 118-125. ZHANG Hongwei, CHEN Jiaqing, ZHANG Yidu. Numerical simulation of shot-peening process based on multiple shot model

[J]. Journal of Plasticity Engineering, 2012, 19(6): 118-125.

[J]. International Journal of Impact Engineering, 2002, 27(2): 119-134.

[J]. Finite Elements in Analysis and Design, 1999, 31: 179-191.

[J]. 建筑结构,2011,41(3): 28-30. YU Wenjing, SHI Jianyong, ZHAO Jincheng. Research of dynamic mechanical behavior of Q345 steel

[J]. Building Structure, 2011, 41(3): 28-30.

[S] . 北京:中国标准出版社,2011.

[S]. 北京:中国标准出版社,2008.

施引文献

附加材料(0)

访问统计

点击查看大图

计量

文章访问数: 1112
HTML全文浏览量: 76
PDF下载量: 506
被引次数: 0

钢板喷丸处理残余应力场和表面粗糙度数值模拟

doi: 10.3969/j.issn.0258-2724.2015.04.018

作者简介: 强斌(1987-),男,博士研究生,研究方向为钢桥焊接的应力与变形控制,E-mail:binqiang1987@163.com

通讯作者: 李亚东(1956-),男,教授,博士生导师,研究方向为桥梁设计理论与施工控制、钢桥稳定与疲劳等,E-mail:ydli@swjtu.cn

计量

出版历程

Numerical Simulation of Residual Stress Field and Surface Roughness for Steel Plate Subjected to Shot Peening

计量

出版历程

目录

作者简介:
强斌(1987-),男,博士研究生,研究方向为钢桥焊接的应力与变形控制,E-mail:binqiang1987@163.com

通讯作者:
李亚东(1956-),男,教授,博士生导师,研究方向为桥梁设计理论与施工控制、钢桥稳定与疲劳等,E-mail:ydli@swjtu.cn