| Citation: | CAO Ao, GAO Hongli, FAN Shuwei, LEI Yuncong, YOU Zhichao. Dynamic Characteristics of TBM Main Bearing under Coupled Excitation of Manufacturing Errors and Local Defects[J]. Journal of Southwest Jiaotong University. doi: 10.3969/j.issn.0258-2724.20250263 |
The main bearing is a critical power transmission component in the main drive system of a tunnel boring machine (TBM). The presence of local defects and surface manufacturing errors induces abnormal vibration in the main bearing. To address the challenges of dynamic modeling under the coupled excitation of these two factors, a multi-fault dynamic model for the TBM main bearing was proposed by incorporating a manufacturing error excitation function into the Gupta bearing dynamic model. This model comprehensively considers the coupled excitation of manufacturing errors and local defects. The validity of the model was verified through experimental results. Building upon this, the effects of local defects and manufacturing errors on the roller-raceway contact load of the main bearing were explored. The mechanism by which their coupled excitation affects the vibration characteristics of the main bearing was revealed, and the sensitivity of the main bearing vibration characteristics to changes in local defect width and depth was analyzed. The results indicate that surface manufacturing errors alter the vibration excitation pattern of local defects, introducing several random components in the low-frequency range, thus complicating the vibration characteristics of the main bearing. As the local defect width increases, the overall main bearing vibration level initially rises gradually. When the defect width reaches the critical dimension of the roller contact area, the vibration level decreases slightly before gradually increasing again. The influence of local defect depth on the main bearing vibration characteristics is relatively weak. The vibration level only increases slowly as the depth grows, but the overall change is minimal. The findings provide a theoretical basis for fault identification in TBM main bearings.
| [1] |
Wang X Q, Wang L T, Chi H S, et al. Uncertainty design optimization of the main bearing in tunnel boring machine based on the Kriging model with partial least squares[J]. Tunnelling and Underground Space Technology, 2025, 162: 106648. doi: 10.1016/j.tust.2025.106648
|
| [2] |
Zhong T, Qin C J, Shi G, et al. A residual denoising and multiscale attention-based weighted domain adaptation network for tunnel boring machine main bearing fault diagnosis[J]. Science China Technological Sciences, 2024, 67(8): 2594-2618. doi: 10.1007/s11431-024-2734-x
|
| [3] |
杨岗, 邓琴, 徐五一, 等. 基于频谱重构的经验傅里叶分解算法及轴承故障诊断应用[J]. 西南交通大学学报, 2026, 61(2): 329-340. doi: 10.3969/j.issn.0258-2724.20240050
Yang Gang, Deng Qin, Xu Wuyi, et al. Empirical Fourier decomposition algorithm based on spectrum reconstruction and its application in bearing fault diagnosis[J]. Journal of Southwest Jiaotong University, 2026, 61(2): 329-340. doi: 10.3969/j.issn.0258-2724.20240050
|
| [4] |
Zheng J Y, Hu S, Ji J C, et al. A review of fatigue failure and structural design of main bearings in tunnel boring machines based on engineering practical examples[J]. Engineering Failure Analysis, 2024, 163: 108611. doi: 10.1016/j.engfailanal.2024.108611
|
| [5] |
Cheng Y J, Wang Y S, Lin J H, et al. Research status of the influence of machining processes and surface modification technology on the surface integrity of bearing steel materials[J]. The International Journal of Advanced Manufacturing Technology, 2023, 125(7/8): 2897-2923. doi: 10.1007/s00170-023-10960-x
|
| [6] |
周扬, 周瑾, 王艺宇, 等. 考虑界面接触的磁悬浮轴承-转子系统建模及鲁棒控制[J]. 西南交通大学学报, 2024, 59(4): 755-765. doi: 10.3969/j.issn.0258-2724.20230510
Zhou Yang, Zhou Jin, Wang Yiyu, et al. Modeling and robust control of magnetic bearing-rotor system considering interface contact[J]. Journal of Southwest Jiaotong University, 2024, 59(4): 755-765. doi: 10.3969/j.issn.0258-2724.20230510
|
| [7] |
Huo J Z, Zhang Z G, Meng Z C, et al. Dynamic analysis and experimental study of a Tunnel boring Machine testbed under multiple conditions[J]. Engineering Failure Analysis, 2021, 127: 105557. doi: 10.1016/j.engfailanal.2021.105557
|
| [8] |
Zong H Y, Wang H, Hong R J. Dynamic research on single-row slewing bearing with local spalling of inner ring[J]. Advances in Mechanical Engineering, 2016, 8(2): 1687814016632488.
|
| [9] |
江泽鹏, 王志伟, 段文军, 等. 回转支承局部故障动力学建模及仿真分析[J]. 重庆理工大学学报(自然科学), 2022, 36(8): 152-160.
Jiang Zepeng, Wang Zhiwei, Duan Wenjun, et al. Dynamics modeling and simulation analysis of slewing bearing with local fault[J]. Journal of Chongqing University of Technology (Natural Science), 2022, 36(8): 152-160.
|
| [10] |
陈威, 苏建新. 基于FRANC3D的盾构机主轴承疲劳作用机理研究[J]. 机械传动, 2022, 46(6): 102-107. doi: 10.16578/j.issn.1004.2539.2022.06.015
Chen Wei, Su Jianxin. Study on fatigue mechanism of main bearings of shield machine based on FRANC3D[J]. Journal of Mechanical Transmission, 2022, 46(6): 102-107. doi: 10.16578/j.issn.1004.2539.2022.06.015
|
| [11] |
孙明帅. 盾构机主驱动系统关键部件局部故障振动特性分析与仿真研究[D]. 济南: 山东大学, 2022.
|
| [12] |
Zhang H L, Qu C Y. Research on tunnel-boring machine main bearing fatigue damage and vibration response[J]. Metals, 2023, 13(4): 650. doi: 10.3390/met13040650
|
| [13] |
Zhou P, Wang Q, Li W, et al. Effect of structural parameters on the vibration of slewing bearing under external loading[J]. Shock and Vibration, 2025, 2025: 6994298. doi: 10.1155/vib/6994298
|
| [14] |
Liu J, Xue L, Xu Z D, et al. Vibration characteristics of a high-speed flexible angular contact ball bearing with the manufacturing error[J]. Mechanism and Machine Theory, 2021, 162: 104335. doi: 10.1016/j.mechmachtheory.2021.104335
|
| [15] |
Liu J, An C Y, Pan G. A vibration model of a rotor system with the sinusoidal waviness by using the non-Hertzian solution[J]. Proceedings of the Institution of Mechanical Engineers, Part K: Journal of Multi-body Dynamics, 2022, 236(1): 151-167. doi: 10.1177/14644193211065916
|
| [16] |
Liu J, Xu Y J, An Y C, et al. Vibration simulation of a ball bearing with the combined imperfections and velocity fluctuations[J]. Mechanics Based Design of Structures and Machines, 2024, 52(1): 408-424. doi: 10.1080/15397734.2022.2116341
|
| [17] |
Xu M M, Miao D X, Gao Y, et al. A bearing dynamic model based on novel Gaussian-filter waviness characterizing method for vibration response analysis[J]. Tribology International, 2024, 194: 109433. doi: 10.1016/j.triboint.2024.109433
|
| [18] |
Su S M, Cao H R, Zhang Y Y. Dynamic modeling and characteristics analysis of cylindrical roller bearing with the surface texture on raceways[J]. Mechanical Systems and Signal Processing, 2021, 158: 107709. doi: 10.1016/j.ymssp.2021.107709
|
| [19] |
Cao H R, Su S M, Jing X, et al. Vibration mechanism analysis for cylindrical roller bearings with single/multi defects and compound faults[J]. Mechanical Systems and Signal Processing, 2020, 144: 106903. doi: 10.1016/j.ymssp.2020.106903
|
| [20] |
侯东晓, 石俊祥, 张博, 等. 工作辊轴承滚道波纹度故障下板带轧机垂直振动特性研究[J]. 振动与冲击, 2024, 43(18): 232-238, 266. doi: 10.13465/j.cnki.jvs.2024.18.025
Hou Dongxiao, Shi Junxiang, Zhang Bo, et al. Vertical vibration characteristics of a strip mill under the fault of raceway waviness of work roll bearing[J]. Journal of Vibration and Shock, 2024, 43(18): 232-238,266. doi: 10.13465/j.cnki.jvs.2024.18.025
|
| [21] |
Yu Y X, Guo L, Chen Z G, et al. Skidding characteristics of urban rail vehicle axle-box bearings considering surface waviness on races[J]. Journal of Vibration and Control, 2024, 30(11/12): 2512-2527. doi: 10.1177/10775463231179857
|
| [22] |
Yang M H, Lu H, Zhang X B, et al. Influence of surface waviness of journal and bearing bush on the static characteristics of hydrodynamic bearing[J]. Processes, 2021, 9(1): 110. doi: 10.3390/pr9010110
|
| [23] |
王展, 陈思阳, 王子男, 等. 考虑动态波纹的陶瓷轴承-转子系统非线性振动特性研究[J]. 机械工程学报, 2024, 60(23): 189-204. doi: 10.3901/JME.2024.23.189
Wang Zhan, Chen Siyang, Wang Zinan, et al. Research on nonlinear vibration characteristics of ceramic bearing-rotor system considering dynamic waviness[J]. Journal of Mechanical Engineering, 2024, 60(23): 189-204. doi: 10.3901/JME.2024.23.189
|
| [24] |
高宏力, 孙弋, 郭亮, 等. 机械加工质量预测研究现状与发展趋势[J]. 西南交通大学学报, 2024, 59(1): 121-141. doi: 10.3969/j.issn.0258-2724.20220085
Gao Hongli, Sun Yi, Guo Liang, et al. Research status and development trend of machining quality prediction[J]. Journal of Southwest Jiaotong University, 2024, 59(1): 121-141. doi: 10.3969/j.issn.0258-2724.20220085
|
| [25] |
Zhuang H, Ding J G, Chen P, et al. Effect of surface waviness on the performances of an aerostatic thrust bearing with orifice-type restrictor[J]. International Journal of Precision Engineering and Manufacturing, 2021, 22(10): 1735-1759. doi: 10.1007/s12541-021-00567-1
|
| [26] |
Zhang H G, Cai J L, Yang T Y, et al. Influence of bearing waviness on the lubrication performances of coupled journal-thrust water-lubricated bearings[J]. Surface Topography: Metrology and Properties, 2023, 11(2): 025025. doi: 10.1088/2051-672X/acdc3f
|
| [27] |
Palmgren A, Palmgren G, Ruley B. Ball and roller bearing engineering[M]. Philadelphia: SKF industries inc. , 1945.
|
| [28] |
Cao A, Gao H L, Fan S W, et al. Study on vibration mechanism and dynamic characteristics for TBM main bearing defects[J]. Mechanical Systems and Signal Processing, 2025, 222: 111807. doi: 10.1016/j.ymssp.2024.111807
|
| [29] |
Sawalhi N, Randall R B. Simulating gear and bearing interactions in the presence of faults Part I. The combined gear bearing dynamic model and the simulation of localised bearing faults[J]. Mechanical Systems and Signal Processing, 2008, 22(8): 1924-1951. doi: 10.1016/j.ymssp.2007.12.001
|
| [30] |
Liu J, Xu Z D, Xu Y J, et al. An analytical method for dynamic analysis of a ball bearing with offset and bias local defects in the outer race[J]. Journal of Sound and Vibration, 2019, 461: 114919. doi: 10.1016/j.jsv.2019.114919
|